Litter-Robot 3: Troubleshooting Step-By-Step Guide (2024)

If you've been troubleshooting issueswith your Litter-Robot 3 to no avail, try this Litter-Robot 3 troubleshooting method, the Fresh Restart. This will help eliminate confounding conditions and identify the problem if there is one. This process will help you communicate the issue to our Customer Service team, so you can get your Litter-Robot working again.

Don't forget to check our Litter-Robot 3 light troubleshooting guide too.

Litter-Robot 3 Troubleshooting: Fresh Restart

It is important that you carry out this entire process through Step 10, no matter if anearlier step has apparently resolved the issue.

Step 1: Power Down

Press the Power button to turn the unit off, then unplug the power supply from the back of the Base.

Litter-Robot 3: Troubleshooting Step-By-Step Guide (1)

Litter-Robot 3: Troubleshooting Step-By-Step Guide (2)

Step 2: Disassemble the Bonnet and Globe

Remove the Bonnet by depressing the side tabs, tilting it backward, then lifting up, and set it aside.

Litter-Robot 3: Troubleshooting Step-By-Step Guide (3)

Litter-Robot 3: Troubleshooting Step-By-Step Guide (4)

Thenremove the Globe and set it aside (you do not have to empty it of litter). We've assumed that your Globe was at the Home position with the litter resting on the black liner, but if your Globe wasn't at the Home position, be careful not to spill litter out of the waste port.

Step 3: Situate the Base

Ensure the Base is properly situated on firm, level flooring, that it is not pushed against anything (like the wall), and nothing is resting on it.If you have your Litter-Robot on carpeting or flooring with cracks, grout lines in the case of tile, or any other deformity that could result in uneven contact, either relocate the unit, or place a board underneath it. Forthe Cat Sensor to workaccurately and reliably, the Litter-Robot must always be free-standing, meaning it's not leaning on anything and nothing is leaning on it.

Empty the Waste Drawer (even if it's not very full).

Litter-Robot 3: Troubleshooting Step-By-Step Guide (5)

Step 4: Reassemble the Globe

Put the Globe back on the unit in the Home position, ensuring that it is on the track.

Litter-Robot 3: Troubleshooting Step-By-Step Guide (6)

If you feel that one side of the Globe is heavier than the other, peer through the screen intothe litter pocket (the area where clean litter is held during a cycle). Any weight concealed here could throw off the unit during cycling. Check for stuck litter, especially if you recently cleaned your unit (leftover moisture may have interacted with the litter). If you see debris or suspect there is litter caked behind the screen, you will need to cleanthe Globe (the screen should not be bent outward to clean behind).

Once aligned on the track, check that the litter level inside the Globe is at or below thethe raised Fill Line on the black rubber liner when spread flat.

Litter-Robot 3: Troubleshooting Step-By-Step Guide (7)

Step 5: Reassemble the Bonnet and Position the Internal Shield & Key

Replace the Bonnet by first aligning the rear tabs in the Base, then tilting the Bonnet forward, and snapping the side tabs into place. Make sure all four tabs are secured.

Litter-Robot 3: Troubleshooting Step-By-Step Guide (8)

Litter-Robot 3: Troubleshooting Step-By-Step Guide (9)

At the back of the Globe, rotatethe black Key intopocket in the Base.

Litter-Robot 3: Troubleshooting Step-By-Step Guide (10)

Step 6: Double Check

Ensure no part of the unit is pushed against a wall or has anything resting onit.

Step 7: Power Up

Plug the power supply back into the Base, and press Power to turn the unit on.

Litter-Robot 3: Troubleshooting Step-By-Step Guide (11)

Litter-Robot 3: Troubleshooting Step-By-Step Guide (12)

Step 8: Automatic Reset

The unit should perform an initial Clean cycle: the Globe will rotate counterclockwise to the Dump position, then rotate clockwise past the Home position to level the litter before returning to the Home position with a solid blue light. The Cat Sensor is automatically reset at the end of eachcycle.

Step 9: Test Cycle

Press Cycle again to test that your unit can complete a Clean cycle and return to the Home position with a solid blue light. Continue to Step 10.
Litter-Robot 3: Troubleshooting Step-By-Step Guide (13)

Step 10: Manual Cat Sensor Activation

Press on the Globe just above the entrance in a forward and downward direction—just press and release. The blue light should turn offand the red light should come on. You'veactivated the Cat Sensor to simulate your cat entering the Globe, then exiting. Allowthe Wait Time (3, 7, or 15 minutes—whatever you have your unit set to) to elapse and the Clean cycle to finish. The Globe will return to the Home position with a solid blue light on the Control Panel; if you get this result,there is no issue with yourLitter-Robot.

If, during Steps 9 or 10, the unit does not return Home with a solid blue light, please note the light pattern and position of the Globe. This information will help Customer Experience advise you on further troubleshooting, so you can get your Litter-Robot working again!

For more information about the Litter-Robot 3, review the Instruction Manual,visit our Support Portal, or check out our YouTube channel.

Recommended

Litter-Robot 3: Troubleshooting Step-By-Step Guide (2024)

References

Top Articles
A True Houndsman: It's More than Hunting with Hounds - Union Sportsmen's Alliance
Articles - Phipps Big Game Hounds
Hotels Near 6491 Peachtree Industrial Blvd
Walgreens Harry Edgemoor
Danielle Moodie-Mills Net Worth
Wordscapes Level 6030
East Cocalico Police Department
Voorraad - Foodtrailers
What Was D-Day Weegy
Mivf Mdcalc
Lantana Blocc Compton Crips
How to watch free movies online
Cooktopcove Com
2024 U-Haul ® Truck Rental Review
272482061
Khiara Keating: Manchester City and England goalkeeper convinced WSL silverware is on the horizon
Trivago Sf
Unforeseen Drama: The Tower of Terror’s Mysterious Closure at Walt Disney World
Pecos Valley Sunland Park Menu
Accuweather Minneapolis Radar
Jurassic World Exhibition Discount Code
1636 Pokemon Fire Red U Squirrels Download
Big Boobs Indian Photos
Little Einsteins Transcript
Tripcheck Oregon Map
Blush Bootcamp Olathe
Prévisions météo Paris à 15 jours - 1er site météo pour l'île-de-France
Bi State Schedule
Craigslist Cars And Trucks Mcallen
Wisconsin Volleyball Team Leaked Uncovered
Sf Bay Area Craigslist Com
Fbsm Greenville Sc
Emily Katherine Correro
The Hoplite Revolution and the Rise of the Polis
Police Academy Butler Tech
Greater Keene Men's Softball
Raisya Crow on LinkedIn: Breckie Hill Shower Video viral Cucumber Leaks VIDEO Click to watch full…
Nancy Pazelt Obituary
Publictributes
Danielle Ranslow Obituary
Emulating Web Browser in a Dedicated Intermediary Box
Pekin Soccer Tournament
Alston – Travel guide at Wikivoyage
How I Passed the AZ-900 Microsoft Azure Fundamentals Exam
60 Days From May 31
Greg Steube Height
Gw2 Support Specter
John Wick: Kapitel 4 (2023)
Joblink Maine
Sapphire Pine Grove
What Does the Death Card Mean in Tarot?
Diesel Technician/Mechanic III - Entry Level - transportation - job employment - craigslist
Latest Posts
Article information

Author: Domingo Moore

Last Updated:

Views: 6039

Rating: 4.2 / 5 (53 voted)

Reviews: 84% of readers found this page helpful

Author information

Name: Domingo Moore

Birthday: 1997-05-20

Address: 6485 Kohler Route, Antonioton, VT 77375-0299

Phone: +3213869077934

Job: Sales Analyst

Hobby: Kayaking, Roller skating, Cabaret, Rugby, Homebrewing, Creative writing, amateur radio

Introduction: My name is Domingo Moore, I am a attractive, gorgeous, funny, jolly, spotless, nice, fantastic person who loves writing and wants to share my knowledge and understanding with you.